Socket Adapter 32A

Socket Adapter 32A on the worksite

A splitter divides one output into several, so more work points can be served without bringing another board to the spot.

Remember that a splitter does not increase available power. The output fuse is the same regardless of how many devices are connected – the total load has to stay within it.

This model is rated 32 A. Size the equipment by the actual simultaneous load – the sum of the nameplate ratings almost always leads to oversizing.

Outputs: 3x32A. Count the work points before choosing – the number of outputs decides how many machines one board can feed.

Where Socket Adapter 32A is used

Typical sites are construction projects, renovations, industrial maintenance and event power. What they share is that the electrical supply is temporary and the conditions are demanding.

Temporary does not mean lighter requirements. Site equipment is exposed to dust, moisture, moving and mechanical stress in a way that fixed installations never are.

Check the load distribution between phases during use. Uneven distribution overloads one phase while the others run half empty, and the usual symptom is a fuse that keeps tripping.

How to choose the right model

The equipment is chosen by rated current and outputs. Start by calculating the simultaneous load and the output types needed, and choose the model on that basis.

You can see the full range in the product group, and read about real-time monitoring on the Spine page.

Practical notes for use

Adapters and splitters are a site’s quick fixes, and for that reason they often stay in use longer than intended. Check their condition regularly and replace worn parts.

Avoid chaining several splitters in series. Every transition is one more place where the connection can work loose, and the voltage drop grows with every metre of cord.

Make sure the RCD protection actually covers the equipment being connected. On a site, RCD protection is the protection that genuinely saves people.

Socket Adapter 32A – installation and maintenance

Installation and connection work is carried out by a qualified electrician. The equipment must be made dead before connection work, and the absence of voltage verified by measurement.

Place the equipment on level ground and so that it can be reached freely even when the site fills up with material. Material stacked in front blocks both use and emergency isolation.

Test the RCD with its test button at commissioning and at regular intervals afterwards. The test takes a second and is still almost always forgotten.

Check the joints and fixings regularly during use. A joint that heats up is a sign of a fault and should be corrected before the fault spreads.

Safety and inspections

Site electrical installations are subject to the same requirements as fixed installations, and some of them are stricter. The equipment has to withstand moving, dust, moisture and mechanical stress for the whole project.

The installation is inspected at commissioning and regularly during use: enclosure, joints, the operation of the protective devices and the fact that live parts cannot be reached.

Damaged equipment is not repaired improvised on site. A cracked enclosure, a burnt terminal or a damaged socket is replaced – on a site a temporary repair almost always becomes permanent.

Document the configuration and any changes made. Up-to-date information on outputs and protection speeds up fault-finding and the next inspection.

Delivery and sizing help

We deliver the equipment together with the cables and the rest of the site power supply in one delivery, so the set is complete when it arrives on site.

Describe the whole site in your request for quotation: supply power, the outputs needed and the estimated length of the project. We size the set on that basis.

Use the product number 2428440 when ordering and when asking about spare parts. It identifies this exact model, which matters when the same series comes in several sizes.

We also help with the sizing. If you are unsure about the size or the number of outputs, ask us – equipment sized wrong costs more than equipment chosen right the first time.

Socket Adapter 32A – technical data

Supply	32A
Output	3x32A

Frequently asked questions

What is the rated current of Socket Adapter 32A?

The rated current is 32 A.

What outputs does the product have?

Outputs: 3x32A.

What is the product number?

The product number is 2428440. Use it in requests for quotation and spare part enquiries.

Who may install the product?

Installation is carried out by a qualified electrician. The requirements are explained in more detail on the Tukes website.

The requirements for electrical installations on worksites are explained in more detail on the Tukes website.

Request a quotation

Add to the quotation basket and send us your request – we will confirm availability and delivery time at the same time. You can see the full range in the product group.